Colmenas y sus piezas

Alimentadores de techo con cobertura completa El alimentador de techo profesional. El mejor instrumento de alimentación. Aíslan el interior de la colmena contra el frio y el calor. Cuando llenan el alimentador no molestáis a las abejas ya que ellas están completamente aisladas. Adecuado para alimentos líquidos (jarabe) y solidos (pasta de azúcar). No tendrán jamás las pérdidas que tenían con los alimentadores de madera. Encaja dentro de la tapa y no cambia la altura de la colmena. Tiene aperturas de ventilación para que pueda salir la humedad de la colmena. No necesita ningún tipo de mantenimiento

Alimentadores de cuadro Flotadores especiales a derecha y a izquierda protegen a las abejas de que se ahoguen. Las paredes interiores tienen relieve para que las abejas puedan subir con facilidad. Se llena desde abajo hacia arriba y no es necesario que le vaciéis de abejas para volver a llenarlo. Ideal para alimentación de colmenas donde se realiza alimentación de reinas. Consejo: En invierno podéis usarlo para delimitar el espacio de las abejas y aislar el enjambre por el costado. La década de 1970 el fundador de ANEL el Sr. Emmanouil Pantelakis diseñó y construyó este tipo de alimentador revolucionando la Apicultura. Esta patente ha obtenido el galardón de plata de APIMONDIA.

The new ANEL LockFit Beehive Bottom Board (Detachable Plastic Ventilated Langstroth Set with Drawer and Door - Available in brown and white) was designed to offer maximum functionality, stability, and ergonomics for every beekeeper. This is a bottom board with multiple capabilities and absolute compatibility with wooden and plastic hive bodies, thanks to its reinforced perimeter frame.

🔸 Key Features

• Screened surface with mesh for excellent ventilation and effective humidity control.

• Collection drawer that fits from both the front and the rear, offering handling flexibility.

  • From the rear, it can be secured for permanent placement.

  • From the front, when inserted, it extends the landing board for a comfortable landing for the bees.

• Guides for vertical division boards, ideal for colony splitting/nucs or special hive management.

• Large holes allowing the bottom board to be screwed onto a pallet, ensuring stability during transport and installation.

• Perimeter frame guaranteeing a perfect fit with every type of hive body, whether wooden or plastic.

• Small perimeter holes allowing for the option of permanently attaching the bottom board to the hive body.

• Optional black feet that snap onto the bottom and prevent soil and stones from entering the holes of the base.

• Special receptor holes for immediate integration of the Big Guy pollen trap without additional modifications.

• When the bottom board is used as a detachable unit, its connection to the hive body is done using metal hive latches/fasteners.

🔸 Entrance Door (Blue or Yellow) The ANEL LockFit door offers security and ease of use:

• It prevents the entry of wasps, death's-head hawkmoths, snakes, or mice, protecting the colony population.

• To close the entrance, simply rotate the door to the solid side (without holes).

• To remove it, press lightly to the right or left; the small pins at the back facilitate easy extraction.

🔸 Drawer & Varroa Monitoring The drawer features grid lines/guides that allow for faster Varroa counting, offering valuable information on the colony's health.

Yet another reason to purchase ANEL detachable bottom boards! With this set you can convert ANEL bottom boards into pollen collectors any time you wish. Its gaps for pollen entrapment have the same shape with those of the classic ANEL collector, not injuring the bees. Pollen is collected in the special trays included in the set. The trays snap and unsnap easily from the front, without the need to move the hive.

Excluidor-barrera vertical Se combina perfectamente con la tapa de la entrada ( AN51670) o el disco de la entrada lateral (AN51676) para que cada parte tenga su propia entrada. De esa manera, cualquier colmena se convierte en dos cincos o tres treses. Para evitar el paso de la reina sobre la barrera vertical, pueden usar los excluidores ( AN51401-4). Si desean evitar también la comunicación entre las obreras (en caso de tres núcleos), pueden usar el tamiz de colección de propóleos (AN58001). • CONSEJO: Abran un agujero de 4mm en cada parte que desean tener una entrada para los enjambres separados, apliquen la tapa de entrada y están listos. Su colmena está equipada con entrada adicional que puede ser útil en el futuro, usada como puerta de ventilación durante los meses calientes.

An innovative new ANEL Product! This is the New Hybrid ANEL Entrance, Ventilation & Feeding Plug.
Multiple uses:
• Ventilation screen and/or feeding plug.
• If you rotate the mechanism, with a simple CLICK, it turns into a small safety entrance for bees.
• Remove the mechanism altogether and you can use it as big entrance or a feeding plug.
To apply it in your beehive you will need:
• A drill with a 43mm hole saw
• Four 3,5 x 13mm screws
• A Polyurethane Sealant
We apply the PU sealant in the inner surface of the plug. We follow the same steps for a wooden beehive. The new ANEL plug is of larger diameter than the previous model. To replace the older model with the new plug you will need a 43mm cylindrical drill. The new plug comes with a hinge and opens sideways. It is advised to open it with a hive tool while holding it from the top, or by hand using our thumbnails. Due to opening sideways the plug cannot be closed by the wind. Position the lid in 90 degrees from the body to remove it. This is very useful because a potential thief will need special equipment.
The new ANEL Entrance, Ventilation & Feeding Plug can be used in many ways. As a feeding plug on the top cover, as ventilation or entrance in the frontside / backside of the top cover, as a small entrance on the side of the beehive protecting the bees from potential enemies, as ventilation on the sides, or as a big hive entrance. An alternative beehive entrance is very important. In case of plunder we leave the small entrance open so that only few bees can come in and the intruders can be handled. We close the front doors and lead the bees on the alternative entrance which the already know and use. For even more drastic measures if we want to prevent plunder, we just seal the plugs on the top cover.
Some other examples of how to use the New ANEL Entrance, Ventilation & Feeding Plug. During spring if we want to use a second hive body, it is very useful to have a second entrance in the upper hive body for beehive decongestion. A second entrance also helps bees collect honey easier, especially if we use a queen excluder.
Also, during spring if we have a ten-frame beehive that is in the process of swarming, we can divide it and have two independent swarms. Half of the frames can be transferred to a new hive body. We use a fabric cover to prevent pheromones from mixing and a queen excluder to keep the two queens away from each other. We place the new hive body on top. The original swarm uses the front entrance, while the new one uses the entrance on the back.
If we want to have 2 swarms in a single beehive, we can provide them two independent entrances from both sides. We keep them divided in two with the help of the ANEL vertical beehive divider. We can also have 3 swarms in the same beehive with the use of 2 dividers. This swarm uses the entrance on the right, this one uses the entrance on the left and the middle swarm uses the entrance on the back. In that case we will need a top feeder to keep them separated and feed them independently with syrup or candy.

A modern tool with many advantages... • Double walled with the gap filled with polyurethane foam insulation. • With 4 ventilation plugs • With feeding plug on top • Unmatched impact strength and load support. • Anti-slip surface to prevent hives from slipping during transportation. • 4 points of attachment at the front, back and the sides (adjustable or wire type). • Resistant to chemicals (caustic potash, oxalic acid, formic acid, bleach etc.). If you use ventilated bottom boards the hive has adequate ventilation even without ventilation caps. Just think of the wild hives settling on the top part of closed spaces, like tree hollows.

Καπάκι Κυψέλης Ξύλινο Lng.

*CAN BE CUT TO ANY SMALLER DIMENSION YOU WISH - CONTACT US! ANEL plastic honeycomb foundation, printed with absolute hexagons (5.6 mm). There is no need for riveting and applying wire on the frames anymore! They can be applied on normal wooden frames that have a slit on the upper and lower part. You can purchase these frames from us, otherwise, with the right tools and very little effort, shape your own existing frames so they can accept the plastic honeycomb foundations.
ANEL plastic honeycomb foundations and frames will not be affected by wax moth. They will remain sturdy and you can use higher speeds in the honey extractor without destroying the honeycomb. Particularly useful for tight honey types. All ANEL plastic honeycomb foundations can come unwaxed or waxed. If you want to wax the foundations yourself you can either dip them in molten wax at a temperature of 60-70ºC or wax them with the help of a roll that you dive into the wax. Made of food-grade plastic. TIP: The ANEL plastic honeycomb foundation can be disinfected in 5% caustic potash solution at 80ºC..

Orientadores para las abejas: ¡ayuda a tus abejas a encontrar su hogar en su camino de regreso!
- Fácil de aplicar
- Reutilizable
- Color electrostático
- ¡Combínalos!
Números magnéticos: numerando sus colmenas FÁCIL, RÁPIDO Y FLEXIBLE
- Elemento magnético potente integrado

Orientadores para las abejas: ¡ayuda a tus abejas a encontrar su hogar en su camino de regreso!
- Fácil de aplicar
- Reutilizable
- Color electrostático
- ¡Combínalos!
Números magnéticos: numerando sus colmenas FÁCIL, RÁPIDO Y FLEXIBLE
- Elemento magnético potente integrado